+8613503854331

Loading and Unloading Operations for Hazardous Chemicals

Nov 03, 2026

In many enterprises, the loading and unloading of hazardous chemicals is a step most prone to being "habitually overlooked"-after all, isn't it just moving goods on or off a vehicle? Yet, this very process is one of the stages where fires, explosions, and leaks involving hazardous chemicals occur most frequently. Loading the wrong vehicle, failing to conduct inspections, neglecting to ground for static electricity, or lacking on-site supervision-a lapse at any point can lead to a disaster. Today, we will examine this process in depth: what does the law actually require regarding the management of hazardous chemical loading and unloading? What are the specific responsibilities of the person in charge of loading, the loading/unloading supervisor, and the safety director?
01 Setting the Tone: Loading and unloading is not merely "routine handling"; it is a process legally required to be conducted under on-site supervision. Let's first correct a common misconception: many believe that loading and unloading is just manual labor that can be handled by drivers and workers coordinating among themselves. ❌ Incorrect view: Anyone present can carry out the loading or unloading of hazardous chemicals.
✅ The official, correct stance: Hazardous chemical loading and unloading operations must adhere to safety standards, procedures, and protocols, and must be carried out under the on-site supervision or monitoring of a designated loading/unloading supervisor. This is explicitly mandated by the *Law on the Safety of Hazardous Chemicals*. In other words, this is not a task to be performed casually; it requires a supervisor to be present to direct or monitor the operation. The absence of such supervision is, in itself, a violation of regulations.
02 Official Requirement: The loader must conduct inspections first-if conditions don't match, do not load. The first line of defense in the loading and unloading of hazardous chemicals is "inspection." The law is very clear on this: before filling or loading hazardous chemicals, the person responsible for loading must fulfill their duty to inspect the shipment and ensure that the filling or loading process complies with established standards. - *Law on the Safety of Hazardous Chemicals*. What, specifically, must be inspected? The "Administrative Measures for the Safety of Road Transport of Dangerous Goods" provides a checklist: ① Vehicles: Do they possess valid vehicle registration certificates and operating permits? ② Personnel: Do the drivers and accompanying attendants hold valid professional qualification certificates? ③ Documentation: Are the consignment notes for dangerous goods, safety data sheets (SDS), and other required papers complete and consistent? ④ Packaging: Do the packaging, labeling, and onboard documentation for the hazardous chemicals meet all regulatory requirements? If any of these criteria are not met, the goods must not be loaded. This constitutes the "consignor/loader's verification responsibility"-if an incident occurs, the party responsible for loading cannot evade liability.
03 Key Focus: "On-site supervision/monitoring" of loading and unloading operations. Determining who is responsible for this is often ambiguous, yet it is the critical factor in assigning liability after an accident. The "Regulations on the Road Transport of Dangerous Goods" explicitly state that loading and unloading operations must adhere to safety standards, procedures, and protocols, and must be conducted under the on-site supervision or monitoring of designated management personnel. Consignors and carriers of dangerous goods are required to appoint such management personnel as per their contractual agreement; if the contract is silent on this, the party responsible for the loading or unloading operation must make the appointment. In plain language: ① Loading and unloading must be supervised; the designated "management personnel" must be qualified and well-versed in the hazardous properties of the chemicals being handled. ② The party responsible for the loading or unloading operation is also responsible for appointing this supervisor-whoever is contractually tasked with the loading/unloading bears the responsibility for on-site supervision and monitoring. ③ If the contract doesn't specify? Then the "party responsible for the loading or unloading operation" must make the appointment. Do not attempt to shift blame between parties; if an incident occurs, liability will inevitably fall on the responsible party.
04 The "Invisible Threat" of Static Electricity: A primary source of danger during filling operations. When handling hazardous chemicals-especially flammable liquids-the most significant and insidious risk is static electricity. The flow of liquid during filling generates static electricity; if it accumulates to a certain threshold, it can ignite vapors and trigger an explosion. Consequently, regulations impose strict requirements regarding filling speeds, feeding methods, and grounding: ① Filling flow rates must be strictly controlled. For the filling of flammable liquids, the flow velocity must be limited to no more than 1 m/s until the fill pipe is submerged below the liquid surface (in accordance with the requirements of GB 12158, "General Requirements for the Prevention of Static Electricity Accidents"). ② Prioritize bottom loading. When filling large containers such as tank trucks with hydrocarbon liquids, bottom loading is preferred; if top loading is used, the fill pipe must extend into the tank to a position no more than 200 mm from the bottom. ③ Ensure hoses are conductive. When transferring flammable liquids via hoses, use conductive hoses or rubber hoses with embedded metal wires/mesh, and ensure electrical continuity for static dissipation. ④ Implement bonding at terminals. Oil loading and unloading terminals must be equipped with anti-static grounding devices for bonding with vessels (as required by standards such as GB 6951). These are not merely "optional" technical details, but critical measures for accident prevention. When a Safety Director oversees loading and unloading operations, static electricity control should be the primary focus.
05 Port/Terminal Operations: The "Reporting" Requirement. If loading or unloading takes place at a port or terminal, the regulations are even stricter. ① Reporting System. The loading, unloading, or transshipment of dangerous goods at a port must be reported in accordance with regulations and authorized before operations can commence; unauthorized operations will result in a mandatory work stoppage and fines. ② Identification of Major Accident Hazards. The Ministry of Transport's "Criteria for Identifying Major Accident Hazards in Port Operations Involving Dangerous Goods" outlines several "veto-worthy" conditions-such as operating beyond the authorized scope, capacity, or time limit; storing dangerous goods in a manner that fails to meet safety requirements; or utilizing equipment, facilities, or safety systems that do not comply with safety standards. In short, port/terminal operations require not only human oversight and static electricity control, but also strict adherence to mandatory reporting and approval procedures.
06 A Safety Director's Checklist for Self-Protection: How to Ensure Accountability in Loading/Unloading Operations. With regulations and legal requirements in place, how should a Safety Director implement them in practice? Here is a practical, actionable checklist: ① Incorporate responsibilities into formal policies. Clearly define who is responsible for loading and unloading operations, identify the designated management personnel, and specify the required certifications; incorporate these details into operational procedures and job descriptions. ② Ensure documentation of pre-loading/unloading inspections. Verify vehicle licenses and permits, personnel qualifications, shipping documents, and packaging-checking each item, recording the results in a "Loading/Unloading Inspection Form," and signing and archiving the document.

Send Inquiry